WELCOME TO CALL US (+86) 18203311200 E-mail: admin@tehold-machine.com
Author: Site Editor Publish Time: 2026-11-11 Origin: Site
We treat broken rice as a product with several buyers, not a loss to be apologised for. That habit changes how we answer an enquiry for a Rice Flour Milling Machine for Commercial Rice Powder Production. Before we discuss a second mill, we ask what the broken kernels are worth today, who buys them and what a powder customer would pay. A line rarely fails because of a machine; it fails because a co-product had no outlet.
We also have to be direct about the limits of our published information. Our rice pages give capacities for the SB series and the 15T and 30T plants, and they list rice graders and sorting machines as category terms. They do not publish a rice flour mill model, a flour fineness, a moisture range, a whiteness value or a powder capacity. So this article is a business case and a specification checklist, not a set of invented machine numbers.
Every rice mill produces a broken fraction, and the first commercial question is where it goes. Some operators sell it as lower-price rice, some send it to feed, some return it to the intake and some grind it into powder. Each route carries a different margin and a different demand on the line. We ask for the current split before we discuss equipment, because a buyer already selling broken kernels well may not need a powder line.
Our SB page describes a low broken rate and output at Grade 1 standard or above, but it gives no percentage and no test method. That matters when you build a forecast: without a broken rate, the volume available to a powder line is an estimate, not a figure we can put in a contract. We ask buyers to weigh a few days of production themselves, then use their own number rather than ours.
Breakage is not a single event at one machine. It accumulates through hulling, whitening, polishing and every transfer in between. Our SB description lists a rubber-roller huller, an air blower separator, an iron-cylinder whitener and a high-pressure fan, with three outlets for white rice, bran and husk. Each of those stages can change the broken fraction, and so can the way the grain is handled after it leaves.
The single rice mill machine is more explicit about the small stream: it separates white rice, fine chaff and small broken rice, and rolls coarse husk back into fine bran that can be used as feed. That is a useful starting point for a co-product plan, because the broken fraction is already separated rather than mixed into the main output. We would rather a buyer start with a measured stream than a projected one.
A powder customer and a low-price rice customer do not want the same broken kernels. Grading decides which fraction goes where, and it has to happen before anyone signs a supply agreement. Our range lists rice graders and rice separators, and the rice grading guide discusses how smaller mills approach that step. We ask buyers to define the size bands they want to sell, not just the word "broken".
The 30T plant description includes a grader alongside its cleaner, husker, polisher and blowers, so grading is part of the train at that scale rather than an afterthought. We must also be careful with language: our category pages use the phrase rice sorting machines, but we publish no optical colour sorter page and no sorter parameters. If a buyer needs optical sorting, that is a separate item to confirm in the RFQ, not something to assume is in the package.
A powder buyer writes a specification sheet, usually more demanding than a rice buyer's. Fineness or mesh, moisture, colour, foreign matter and the test method for each are the terms we see in enquiries. We publish none of those values for rice powder, so we ask for the buyer's sheet and treat it as the specification to design against. Guessing a mesh number to close a quotation would be the wrong start.
The flour sifter is a real item in our single-machine range, and it belongs in that conversation as a grading step. It does not, on its own, tell you what fineness a flour mill will deliver. Where a customer also buys wheat flour, we point to the rice and corn milling overview for context, but we keep the two product specifications separate.
Rice powder specification schedule | ||
Item | Who sets it | Status on our pages |
|---|---|---|
Fineness or mesh | Buyer's customer | Not published |
Moisture limit | Buyer's customer | Not published |
Whiteness or colour | Buyer's customer | Not published |
Broken kernel tolerance | Buyer's customer | Not published |
Pack format and shelf life | Buyer's customer | Not published |
Test method and sampling | Both sides in the RFQ | Not published |
Buyers often ask whether we supply a dry or a wet grinding route, and this is where we have to stop and be clear. Our published pages do not describe a rice flour process, a wet grinding line, a soaking step or a drying step. We cannot tell you which route is right from our catalogue, because we have not published the equipment or the parameters for either. What we can do is help you write the question precisely.
The rice and rice flour mill price guide discusses the commercial side of that decision, and we would rather you use it to frame a budget than to infer a specification. Our hammer mill page does list rice among the grains it can reduce, but it is a feed mill page and publishes no flour fineness. Keep the two scopes apart in the RFQ, or the quotation will be judged against the wrong standard.
The attractive part of a powder line is that it shares the intake, cleaning and sometimes the grading with the rice mill. That is also the part that needs checking. A shared intake means a shared interruption: when paddy cleaning stops, both products stop. We ask buyers to map the flow from intake to each outlet and mark where the two products depend on the same machine, then decide whether that dependency is acceptable.
Where broken kernels can go, and what each outlet requires | |||
Outlet | What it needs | What we publish | To confirm |
|---|---|---|---|
Feed grade | Clean separation from husk | Fine bran as feed on the single mill page | Local feed buyer specification |
Low-price rice | Consistent size band | Rice graders listed in our range | Grading cuts and price band |
Return to intake | Controlled re-milling | Not published | Yield loss on the second pass |
Rice powder | A separate grinding step | No rice flour mill specifications published | Fineness, moisture, whiteness |
We also ask what happens when the broken fraction is smaller than expected. A powder line sized on an optimistic breakage rate will sit idle, and the fixed cost does not shrink with it. Our rice mill machine range shows the capacities we do publish for the rice side, so the intake side of that calculation can be checked. The output side still needs the buyer's own measurements and a signed customer specification.
Rice powder behaves differently from whole rice in storage, and the buyer's customer will ask about pack format, barrier properties and shelf life. We do not publish those values and we will not supply them from a general table. They depend on the flour's moisture and fat content, the pack material, the local climate and the distribution chain. The honest answer is that they belong to the product specification, not to the machine quotation.
What we can put in a contract is the mechanical side of packing: where the finished powder is discharged, how it is weighed, and what equipment sits at that point. Our feed plant pages describe manual weighing and packing, and our wheat lines list packing machines at larger capacities, but neither is a rice powder packing specification. We ask the buyer to name the pack size and the daily bag count so the discharge end can be sized.
Our suggested order is unglamorous. Measure the broken fraction for a representative week. Get a written specification and a price from a powder customer. Work out what the same kernels earn today in their existing outlet. Then list the equipment the powder route needs and ask which of those items we publish, which are listed accessories and which have to be sourced or specified separately. Only then compare the two margins.
We would rather a buyer decide not to add the line than buy one against a forecast built on our gaps. If the customer specification cannot be met with equipment we can document, we say so. Send us your measured broken volume and the powder buyer's sheet, and we will tell you plainly which parts of the flow we can quote from published pages and which need to be agreed in writing first.
A Rice Flour Milling Machine for Commercial Rice Powder Production is the last decision in this chain, not the first. The broken fraction, the grading cuts, the customer's specification and the economics of the existing outlet all come before it. We have tried to give you the sequence we use to test that decision, including the places where our own pages stop.
Tehold International supplies grain cleaning, drying, storage, milling and packaging equipment as turnkey packages, and we would rather help you measure a co-product stream than quote a flour fineness we have not published. We publish rice mill capacities, the SB flow and our grading and single-machine range. Rice flour mill models, fineness, moisture, whiteness and powder capacity are not published and must be agreed in the RFQ.
No. Our rice pages publish SB series capacities and the 15T and 30T plant descriptions, and they list rice graders and sorting machines as category terms. They do not publish a rice flour mill model, flour fineness, moisture range, whiteness value or powder capacity. We ask for your customer's specification sheet and work from that rather than supply a number we cannot stand behind.
Not as a published item. Our category pages use the phrase rice sorting machines, but we have no optical colour sorter product page or parameters. Our published grading discussion is about size and length grading, destoning and broken kernel separation. If your product needs optical sorting, put it in the RFQ as a separate item so the supply scope is unambiguous.
We would not present it that way. Our hammer mill page lists rice among the grains it can reduce, but it is a feed mill page and publishes no flour fineness or target particle size in microns. A powder buyer's specification is a different standard. Keep the two scopes separate in the enquiry so the equipment is judged against the right test.
We cannot give you a percentage. Our SB page describes a low broken rate and output reaching Grade 1 standard or above, but gives no figure or test method. Breakage depends on paddy variety, moisture, handling and the whitener setting. We ask buyers to weigh the broken stream over a representative week and use their own measurement for the business case.
Only after you have a written customer specification, a price, and a measured broken volume. Compare that margin against what the same kernels earn in their current outlet, then list which equipment we can quote from published pages and which must be specified separately. We would rather you defer the purchase than build a forecast on figures we have not published.
